7850 NSG-X Activation
Back to Other Form Factors
Please refer to your service provider's documentation.
Setting Up 7850 NSG-X
- Connect your 7850 NSG-X to one or more AC power supplies (100-240V).
- Connect the WAN connection to one of:
- Ports 1-2, which are 10 Gigabit Ethernet SFP+ ports
- Ports 3-5, which are Gigabit Ethernet electrical ports
Note: multiple ports may be used for uplink connectivity. Refer to your service provider’s detailed documentation for further information.
- For automatic bootstrap mode, insert the USB bootstrap key into any USB port and power-on the NSG.
- For multi-factor bootstrapping, the installer must connect the laptop to Gigabit Ethernet Port 6 (identified by a blinking LED), power-on the NSG and follow the instructions in the bootstrap email.
- Post bootstrapping, connect devices to any available ports (i.e. not used for WAN connection) using Ethernet cable(s).
||Multicore Intel™ Xeon D
- 4 x 10/100/1000BASE-T Gigabit Ethernet (RJ45)
- 4 x 1000BASE Ethernet (SFP)
- 2 x 10GBASE Ethernet (SFP+)
- 2 x USB 3.0 Standard-A female
- 1 x RS-232 RJ-45 console
||Redundant, field replaceable AC power supply units
||430 mm x 500 mm x 44 mm / 17 in. x 19.7 in. x 1.7 in. (width x depth x height)
||10 Kg / 22 lb
||0 ~ 40°C / 32° ~ 104°F
|Operating relative humidity
||5 ~ 85% @40°C (104°F)
- Draw: 300 W (maximum)
- Input: 100 ~240 V at 50-60 Hz, full range
||Back to Front airflow
- Built-in Trusted Platform Module
- Chassis intrusion detection
||Dedicated Intel® QuickAssist
||Included rack mount kit
Front Panel Features of 7850 NSG-X
||Software reset button
||Hard disk activity LED (all SATA devices)
||Software controlled LED 1
||Software controlled LED 2
||RS232 Console +
||Stacked Type A USB connector providing 2 USB2.0/3.0 ports
||2x 10G SFP+
||Management Port A1/A2
||Management LAN Port A1/A2
||Traffic Port 1~6
||1GbE RJ45 port 3-6
||1NMC slot 4x1GbE SFP and 1 NMCs slot for expansion
Rear Panel Features of 7850 NSG-X
||1 PCIEx8 for Add on card as default option
||3 Rear system fan exhaust
||Power DC on/off button
||PSU Alarm suppression
||Suppress the alarm sound if a PSU is missing
||AC Power inlet
||2 AC Power connector (redundant PSU)
- Keep this equipment away from humidity.
- Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
- Before connecting the equipment to the power outlet make sure the voltage of the power source is correct.
- Position the power cord so that people cannot step on it. Do not place anything over the power cord.
- Please not all cautions and warnings on the equipment.
- If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over-voltage.
- Never pour any liquid into an opening. This may cause fire or electrical shock.
- For safety reasons, the equipment should be opened only by qualified service personnel.
- If one of the following situations arises, get the equipment checked by service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated into the equipment.
- The equipment has been exposed to moisture.
- The equipment does not work as expected.
- The equipment has been dropped and damaged.
- The equipment has obvious signs of breakage.
- The sound pressure level at the operator’s position according to IEC 704-1:1982 is no more than 70 dB (A).
- Do not leave this equipment in an environment where the storage temperature may go beyond the range specified in hardware specifications table. This could damage the equipment. Keep the equipment in a controlled environment at all times.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.
Static Electricity Safety
- Be sure you are at an ESD workstation, or grounded with an ESD strap before opening the top cover or installing/removing any unit accessible from the outside. Doing so will discharge any static electricity that might have built up in your body.
- Don’t touch any components inside the system while the system is on.
- Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components.
- When unpacking a static-sensitive component from its shipping carton, do not remove the component’s antistatic packing material until you are ready to install the component in the unit.
- When transporting any electrical component, first place it in an antistatic container or packaging.
||UL 60950-1 2nd Edition//CSA C22.2 No. 60950-1-07 2nd Edition
||EN 60950-1:2006/A11:2009/A1:2010/A12:2011, EN 60950-1: A2:2013
||CB Certificate and Report to IEC60950-1, 2nd Edition and all international deviations
||FCC 47 CFR Parts 15, Verified Class A Limit
||ICES-003 Class A Limit
- EMC Directive, 2004/108/EC
- EN55022, Class A Limit, Radiated & Conducted Emissions
- EN55024 Immunity Characteristics for ITE
- EN61000-4-2 ESD
- Immunity EN61000-4-3
- Radiated Immunity
- EN61000-4-4 Electrical
- Fast Transient EN61000-4-5 Surge
- EN61000-4-6 Conducted RF
- EN61000-4-8 Power Frequency Magnetic
- Fields EN61000-4-11 Voltage Fluctuations
||CISPR 22, Class A Limit, CISPR 24 Immunity
The CE marking on this product indicates that it is in compliance with the European Union EMC Directive 2004/108/EC, Safety Directive 2001/95/EC, Low Voltage Directive 2006/95/EC, and RoHS (recast) Directive 2011/65/EU.
Back to Other Form Factors