7850 NSG-C Activation
Back to Other Form Factors
Please refer to your service provider's documentation.
Setting Up 7850 NSG-C
- Connect your 7850 NSG-C to the AC power supply (100-240V).
- WAN connection:
- For single-uplinks, use an Ethernet cable to connect to Port 1.
- For dual-uplinks, use Ethernet cables to connect to Ports 1-2.
Note: Please refer to your service provider's detailed documentation for further information.
- Ports 2-3 can be used for connecting to LAN(s).
- For automatic bootstrap mode, insert the USB bootstrap key into any USB port and power-on the NSG.
- For multi-factor bootstrapping, the installer must connect the laptop to Gigabit Ethernet Port 3 (identified by a blinking LED), power-on the NSG and follow the instructions in the bootstrap email.
- Post bootstrapping, connect devices to any available ports (i.e. not used for WAN connection) using Ethernet cable(s).
||Intel® Bay Trail
- 3 x GbE - 10/100/1000 Mbps (RJ45)
- 1 x USB 2.0, 1 x USB 3.0 (backward compatible with USB 2.0)
- 1 x RJ-45 console
- 1 x reset button (hardware reset only)
||124.26 x 19.4 x 119.66 mm (width x height x depth)
||0.5 Kg / 1.1 lbs
||0 ~ 40°C / 32° ~ 104°F
|Operating relative humidity
||0% ~ 90%, non-condensing
- Draw: 36 W (maximum)
- Input: 100 ~240 V at 50-60 Hz
- System: Fanless
- Processor: Passive CPU heatsink
||CE Class B, FCC Class B, RoHS
Front Panel Features of 7850 NSG-C
Rear Panel Features of 7850 NSG-C
- Keep the chassis area clear and dust-free during and after installation.
- Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves.
- Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.
- Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
- Disconnect all power by turning off the power and unplugging the power cord before installing or removing a chassis or working near power supplies.
- Do not work alone if potentially hazardous conditions exist.
- Never assume that power is disconnected from a circuit; always check the circuit.
- Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to acceptable operating temperatures without adequate circulation. Be sure that the room in which you choose to operate your system has adequate air circulation.
- Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An open chassis permits air leaks, which may interrupt and redirect the flow of cooling air from internal components.
Static Electricity Safety
- Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-prevention procedures when removing and replacing components to avoid these problems.
- Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available, ground yourself by touching the metal part of the chassis.
- Periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms).
Lithium Battery Safety
- Risk of explosion if battery is replaced by an incorrect type.
- Dispose off used batteries according to the instructions provided with the equipment.
- Installation must be performed only by a trained electrician or an electrically trained person who understands all the Installation and Device Specifications that are provided in English.
- Do not carry the handle of power supplies when moving to another place.
- The machine can only be used in a fixed location such as a laboratory or computer facilities.
Back to Other Form Factors